GLOSSARY

A

abrasive finish
a flat non-reflective surface finish for marble
abutment
a solid stone "springer" at the lowest point of an arch or vault
adhered
veneer secured and supported through adhesion to an approved bonding material applied over an approved backing
agate
a variegated variety of quartz showing colored bands or other markings (clouded, mosslike, etc.)
anchors
types of stonework include those made of flat stock (strap, cramps, dovetails, dowel, strap and dowel, and two-way anchors) and round stock (rod cramp, rod anchor, eyebolt and dowel, flat-hood wall tie and dowel, dowel and wire toggle bolts)
apex stone
uppermost stone in a gable, pediment, vault or dome
arch
a curved stone structure resting on supports at both extremities used to sustain weight, to bridge or roof an open space
architrave
the member of an entablature resting on the capitals of columns and supporting the frieze
argillite
a compact sedimentary rock composed mainly of clay and aluminum silicate minerals
arkose
a sandstone containing 10% or more clastic grains of feldspar. Also called arkosic sandstone, feldspathic sandstone
arris
a natural or applied line on the stone from which all leveling and plumbing is measured
ashlar
masonry having a face of square or rectangular stones, either smooth or textured

B

back arch
a concealed arch carrying the backing of a wall where the exterior facing is carried by a lintel
baluster
a miniature pillar or column supporting a rail, used in balustrades
balustrade
an ornamental fencing consisting of a series of balusters supporting a handrail or molding
banker
bench of timber or stone on which stone is shaped
basalt
a dense-textured (aphanitic), igneous rock relatively high in iron and magnesia minerals and relatively low in silica, generally dark grey to black, and feldspathic; a general term in contradistinction to felsite, a light-colored feldspathic and highly siliceous rock of similar texture and origin
bed
the top or bottom of a joint, natural bed; surface of stone parallel to its stratification. (1) In granites and marbles, a layer or sheet of the rock mass that is horizontal, commonly curved and lenticular as developed by fractures. Sometimes applied also to the surface of parting between sheets. (2) In stratified rocks the unit layer formed by semidentation; of variable thickness, and commonly tilted or distorted by subsequent deformation; generally develops a rock cleavage, parting, or jointing along the planes of stratification
belt course
a continuous horizontal course of flat stones placed in line marking a division in the wall plane
bevel
when the angle between two sides is greater or less than a right angle
bluestone
a dense, hard, fine-grained, commonly feldspathic sandstone or siltstone of medium to dark or bluish-gray color that splits readily along original bedding planes to form thin slabs. Bluestone is not a technical geologic term. It is considered to be a variety of flagstone, the thin relatively smooth-surfaced slabs being suitable for use as flagging. The term has been applied particularly to sandstones of Devonian age that are being or have been quarried in eastern New York and Pennsylvania and in western New Jersey, but similar stones that occur elsewhere may be included. It has also been applied in places to thinly layered gneisses and schists that can be split and used as flagging, but such stones are not properly embraced by this definition, although they may be marketed properly as flagstone
bond stone
used in varying percentages to anchor or bond the stone veneer to the backing material. Bond stones are generally cut to twice the bed thickness of the material being used
border stone
usually a flat stone used as an edging material. A border stone is generally used to retain the field of the terrace or platform
box
a tapered metal box wedged in the top of columns or other heavy stones for hoisting
broach
to drill or cut out material left between closely spaced drill holes; a mason's sharp-pointed chisel for dressing stone; an inclined piece of masonry filling the triangular space between the base of an octagonal spire and the top of a square tower; a type of chisel used for working narrow surfaces
brownstone
a sandstone of characteristic brown or reddish-brown color that is due to a prominent amount of iron oxide, as interstitial material
brushed finish
obtained by brushing the stone with a coarse rotary-type wire brush
building stone, natural
rock material in its natural state of composition and aggregation as it exists in the quarry and is usable in construction as dimension building stone
bull nose
convex rounding of a stone member, such as a stair tread
buttering
placing mortar on stone with a trowel before setting into place

C

calcarenite
limestone composed predominantly of clastic sand-size grains of calcite, or rarely aragonite, usually as fragments of shells or other skeletal structures. Some calcarenites contain oolites (small, spherical grains of calcium carbonate that resemble roe) and may be termed oolite limestone. Calcareous sandstones, in which the calcium carbonate is present chiefly as bonding material, are not included in this category
calcite limestone
a limestone containing not more than 5% of magnesium carbonate
calcite streaks
description of a white or milky-like streak occurring in stone. It is a joint plane usually wider than a glass seam and has been re-cemented by deposition of calcite in the crack and is structurally sound
canopy
a sheltering roof, as over a niche or a doorway
capital
the culminating stone at the top of a column or pilaster, often richly carved
carve
shaping, by cutting a design to form the trade of a sculptor
caulking
making a marble joint tight or leak-proof by sealing with an elastic adhesive compound
cavity vent
a vent or opening in the joints between stones to provide even atmospheric pressure and humidity between the cavity and outside air; to prevent condensation and the migration of water into the structure
cement putty-cream-butter
a thick creamy mixture made with pure cement and water which is used to strengthen the bond between the stone and the setting bed
chamfer
to bevel the junction of an exterior angle
chat-sawn finish
a rough gangsaw finish produced by sawing with coarse chat
cladding
non-load-bearing thin stone slabs used for facing buildings
cleavage
the ability of a rock mass to break along natural surfaces; a surface of natural parting
cleavage plane
plane or planes along which a stone may likely break or delaminate
coating
a protective or decorative covering applied to the surface or impregnated into stone for such purposes as waterproofing, enhancing resistance to weathering, wear, and chemical action, or improving appearance of the stone
cobblestone
a natural rounded stone, large enough for use in paving; commonly used to describe paving blocks, usually granite, generally cut to rectangular shapes
commercial marble
a crystalline rock composed predominantly of one or more of the following materials: calcite dolomite or serpentine, and capable of taking a polish
composite
a construction unit in which stone that is to be exposed in the final use is permanently bonded or joined to other material, which may be stone manufactured material, that will be concealed
contraction joints
spaces where panels are joined and which expand as the panels contract
control joint
provided so that the movement of different parts of the structure due to shrinkage, expansion, temperature changes or other causes do not transfer loads across the joint
coping
a flat stone used as a cap on freestanding walls
coquina
a limestone composed predominantly of unaltered shells or fragments of shells loosely cemented by calcite. Coquina is generally very coarse-textured and has a high porosity. The term has been applied principally to a very porous shell rock of Eocence age that has been quarried in Florida
corbel plates
plates of non-ferrous metal fixed into a structure to support stone cladding at intervals and over openings in such a way as not to be visible
cornerstone
a stone forming a part of a corner or angle in a wall. Also a stone laid at the formal inauguration of the erection of a building, not necessarily at a corner, usually incorporating a date or inscription
cornice
a molded projecting stone at the top or an entablature
course
a horizontal range of stone units the length of the wall
coursed veneer
this is achieved by using stones of the same or approximately the same heights. Horizontal joints run the entire length of the veneered area. Vertical joints are constantly broken so that no two joints will be over one another
crack
a break, split, fracture, fissure, separation, cleavage, or elongated narrow opening, however caused, visible without magnification to the human eye and extending from the surface into the stone, that must extend through the grain or matrix
cross-bedding
the arrangement of laminations of strata transverse or oblique to the main planes of stratification
crowfoot (styolite)
description of a dark gray to black zigzag marking occurring in stone. Usually structurally sound
crystalline limestone
a limestone, either calcitic or dolomitic, composed of interlocking crystalline grains of the constituent minerals and of phaneritic texture; commonly used synonymously with marble and thus representing a recrystallized limestone; improperly applied to limestones that display some obviously crystalline grains in a fine-grained mass but which are not of interlocking texture and do not compose the entire mass. (NOTE: All limestones are microscopically, or in part megascopically, crystalline, ; the term is thus confusing but should be restricted to stones that are completely crystalline and of megascopic and interlocking texture and that may be classed as marbles)
curbing
slabs and blocks of stone bordering streets, walks, etc
cut stone
this includes all stone cut or machined to give sizes, dimension or shape, and produced in accordance with working or shop drawings which have been developed from the architect's structural drawings
cutting stock
a term used to describe slabs of varying size, finish, and thickness which are used in fabrication treads, risers, copings, borders, sills, stools, hearths, mantels, and other special purpose stones

D

dacite
a fine-grained, extrusive (volcanic) rock, intermediate in color and composition between basalt and rhyolite
damp-proofing
one or more coatings of a compound that is impervious to water applied to a surface above grade
defect
those features which affect or have the potential of affecting the structural soundness of building stone, or may affect the durability of the building stone. Sometimes used for visual features such as xenoliths or veins
dentil
block projections on an entablature
dentil course
the lower part of the cornice with dentils. The cornice is jointed to allow machines production of the dentils
dentils
small, rectangular blocks under a classical cornice, resembling a row of teeth
dimension stone
quarried stones, generally two feet or more square, of a specified thickness. Usually with one or more mechanically dressed surfaces
dolomitic limestone
a limestone rich in magnesium carbonate, frequently somewhat crystalline in character, found in ledge formations in a wide variety of color tones and textures. Generally speaking, its crushing and tensile strengths are greater than the oolitic limestones and its appearance shows greater variety in texture
dowel
a short piece of non-ferrous metal or slate fixed into a mortise or sinking in the joints of adjoining stones to prevent movement
dressed or hand-dressed
the cutting of rough chunks of stone by hand to create a square or rectangular shape. A stone which is sold as dressed stone generally refers to stone ready for installation. Sometimes called scabbling
drip
a recess cut beneath and slightly behind projecting stone to prevent water from running down the face of the wall below
dripstone
a projecting moulding over the heads of doorways, windows and archways to throw off the rain. Also known as a "hoodmould" and, when rectangular, as a "label"
dry
an open or unhealed joint plane not filled with calcite and not structurally sound
dry wall
a dry wall is a stone wall that is constructed one stone upon the other without the use of any mortar. Generally used for retaining walls
durability
the measure of the ability of natural building stone to endure and to maintain its essential and distinctive characteristics of strength, resistance to decay, and appearance, with relation to a specific manner, purpose, and environment of use

E

efflorescence
a crystalline deposit appearing on stone surfaces typically caused by soluble salts carried through or onto the stone by moisture, which has sometimes been found to come from brick, tile, concrete blocks, cement, mortar, concrete, and similar materials in the wall or above
entablature
in classical architecture, the upper part of an order, comprising architrave,
frieze, and cornice
entasis
the curve of the upper two-thirds of a column
expansion bolt
a socket that grips a drilled hole in stone by expanding as the bolt is
screwed into it
expansion-contraction joint
a joint in a wall designed to allow the expansion and contraction of the wall due to temperature change. An expansion joint compresses as panels expand, a contraction joint expands as panels contract
exposed aggregate
phrase applied to the larger pieces of stone aggregate
purposefully exposed for their color and texture in a cast slab

F

face
this refers to the exposed portion of stone. The word "face" can also be used when referring to the edge treatment on various cutting stock materials
fascia
a horizontal belt or vertical face; often used in combination with moldings
ferruginous
limestone or sandstone containing a high proportion of iron oxide
field stone
loose blocks separated from ledges by natural process and scattered through or upon the regolith ("soil") cover; applied also to similar transported materials, such as glacial boulders and cobbles
filling
filling the natural voids and veins in a stone with material (cement, shellac, or synthetic resins and similar materials often mixed with stone fines)
fines
the residue resulting from the normal fabrication and processing of stone
finish
the final appearance exposed stone slab surfaces are fabricated to meet
finished stone
building stone with one or more mechanically dressed surface(s)
fireproof
relatively incombustible
flagstone
thin slabs of stone used for flagging or paving walks, driveways, patios, etc.
It is generally fine-grained sandstone, bluestone, quartzite or slate, but thin slabs of
other stones may be used
fleuri cut
cutting quarried marble or stone parallel to the natural bedding plane
flooring
stone used as an interior pedestrian wearing surface
fracture
a break in rock produced by mechanical failure. Fractures include faults and
joints
freestone
a stone that may be cut freely in any direction without fracture or splitting
frieze
a belt course, sometimes decorated with sculpture relief, occurring just under a cornice

G

gang sawed
description of the granular surface of stone resulting from gangsawing alone
gauged or gauging
a grinding process to make all pieces of material to be used together the same thickness
glass seam
description of a narrow glass-like streak occurring in stone; a joint plane that has been re-cemented by deposition of translucent calcite in the crack and is structurally sound
grade course
beginning course at the grade level, generally waterproofed with a dampcheck or damp course
grain
the easiest cleavage direction in a stone. "With the grain" same as "natural bed". Also, particles (crystals, sand grains, etc.) of a rock
granite
a fine to coarse-grained, igneous rock formed by volcanic action consisting of quartz, feldspar, and mica, with accessory minerals. Granite-type rocks include those of similar texture and origin.granite (scientific definition) a visibly granular, crystalline rock of predominantly interlocking texture, composed essentially of alkalic feldspars and quartz; this is true granite. Feldspar is generally present in excess of quartz, and accessory minerals (chiefly micas, hornblende, or more rarely pyroxene) are commonly present. The alkalic feldspars may be present (1) as individual mineral species, (2) as isomorphous or mechanical intergrowths with each other, or (3) as chemical intergrowths with the lime feldspar molecule, but 80 + 3% of the feldspar must be composed of the potash or soda feldspar molecules
granite (commercial/building use)
a term that includes granite (as defined above), gneiss, gneissic granite, granite gneiss, and the rock species known to petrologists as syenite, monzonite, and granodiorite, species intermediate between them, the gneissic varieties and gneisses of corresponding mineralogic compositions and the corresponding varieties of porphyritic textures. The term commercial granite shall also include other feldspathic crystalline rocks of similar textures, containing minor amounts of accessory minerals, used for special decorative purposes, and known to petrologists as anorthosite and laurvikite
granite gneiss
a foliated crystalline rock composed essentially of silicate minerals with interlocking and visibly granular texture, and in which the foliation is due primarily to alternating layers, regular or irregular, of contrasting mineralogic composition. In general a gneiss is characterized by relatively thick layers as compared with a schist. According to their mineralogic compositions, gneisses may correspond to other rocks of crystalline, visibly granular, interlocking texture, such as those included under the definition of commercial granite, and may then be known as granite gneiss if strongly foliated, or gneissic granite if weakly foliated
black granite
rock species known to petrologists as diabase, diorite, gabbro, and intermediate varieties are sometimes quarried as building stone, chiefly for ornamental use, and sold as "black granite". As dimension blocks or slabs, they are valued specifically for their dark grey to black color when polished. Scientifically, they are far removed in composition from true granites though they may be satisfactory used for some of the purposes to which commercial granites, are adapted. They possess an interlocking crystalline texture, but unlike granites, they contain little or no quartz or alkalic feldspar, and are characterized by an abundance of one or more of the common black rock-forming minerals (chiefly pyroxenes, hornblende, and biotite)
granular
having a texture characterized by particles that are apparent to the unaided eye. For sedimentary rocks; particles less than 4 inches (10 mm) in diameter and approximately equal in size
greenstone
includes stones that have been metamorphosed or otherwise changed so that they have assumed a distinctive greenish color owing to the presence of one or more of the following minerals: chlorite, epidote, or actinolite
grout
pourable cementitious material. COARSE GROUT, used for wide grout spaces 2" or more, consists of one part Portland cement, two-and-a-quarter to three parts sand, and one to two parts pea gravel. FINE GROUT, used in narrow grout spaces, consists of one part Portland cement and two-and-a-quarter to three parts sand

H

hand-cut random rectangular ashlar
a pattern where all stone is hand cut into squares and rectangulars. Joints are fairly consistent. Similar to sawed-bed ashlar in appearance
hand or machine pitch-faced (rock-faced) ashlar
a finish given to both veneer stone and cutting stock. This is created by establishing a straight line back from the irregular face of the stone. Proper tools are then used to cut along the line, leaving a straight arris and the intended rustic finish on the face
head
the end of a stone which has been tooled to match the face of the stone. Heads are used at outside corners, windows, door jambs, or any place where the veneering will be visible from the side
hearth
that part of the floor of a fireplace of stone on which the fire is laid
hearth stone
originally the single large stone or stones used for the hearth, now most commonly used to describe the stone in front of the fire chamber and many times extending on either or both sides of the front of the fire chamber
holes
sinkages in the top beds of stone to engage Lewis pins for hoisting
honed finish
honed is a super fine smooth finish, though not as fine as a polished finish

I

igneous
one of the three great classes of rock (igneous, sedimentary and metamorphic), solidified from molten slate, as granite and lavas
incise
to cut inwardly or engrave, as in an inscription
inscription
lettering cut in stone

J

jack arch
one having horizontal or nearly horizontal upper and lower surfaces. Also called flat or straight arch
joint
the space between stone units, usually filled with mortar
jointing scheme
a detailed architectural drawing showing the dimensions, locations and configurations of stone units and joints on the structure
jumper
in ashlar patterns, a piece of stone of higher rise than adjacent stones which is used to end a horizontal mortar joint at the point where it is set

K

keystone
the last wedge-shaped stone placed in the crown of an arch, regarded as binding the whole

L

lava
a general term applied to igneous rocks, such as basalt and rhyolite, that erupted from the earth by volcanic action
lead buttons
lead spacers in the solid horizontal joints to support the top stone until the mortar has set
lewis bolt
a tapered head wedged in a tapered recess in stone for hanging soffit stones
lewis holes
holes in cut stone for lifting and support during setting of cut stones and sometimes for permanent support. Holes are checked for the particular Lewis lifting device or hook to be used
limestone
a sedimentary rock composed of calcium carbonate; includes many varieties. (See oolitic limestone, dolomitic limestone, crystalline limestone). Limestones that contain not more than five per cent magnesium carbonate may be termed calcite limestone, as distinguished from those that contain between five and 40 per cent magnesium carbonate (magnesium or dolomitic limestone), and from those that contain in excess of 40 per cent as the mineral dolomite (dolostone, formerly known as the rock dolomite). Recrystallized limestones and compact, dense, relatively pure microcrystalline varieties that are capable of taking a polish are included in commercial marbles
liners
strengthening elements attached to the back of stone slabs, usually a structurally sound section of similar stone dowelled and epoxied into place
lintel
the block of stone spanning the top of an opening such as a doorway or window; sometimes called a head
lipping
usually refers to flagging materials; caused when two pieces of material to be joined together are slightly warped or twisted causing one or more edges to be higher or lower than the adjoining material
lug sill
a stone sill set into the jambs on each side of masonry openings

M

machine finish
the generally recognized standard machine finish produced by the planers
malpais
literally, badland; refers to dark colored rock, commonly lava, in rough terrain. As defined for architectural use; calcium carbonate with other components which give it color, markings, and texture suitable as a desirable building stone
marble
a metamorphic limestone in a more or less crystalline state capable of taking a high polish. Occurs in a wide range of colors and variations. Marble that contains less than five percent magnesium carbonate may be termed calcite marble; from 5 to 40 percent magnesium carbonate, magnesian or dolomitic marble; and more than 40 percent dolomite marble. These limiting values are, however, not strictly established in petrologic science and are used herein as arbitrary limits
masonry
built up construction, usually of a combination of materials set in mortar
metamorphism
the change or alteration in a rock caused by exterior agencies, such as deep-seated heat and pressure, or intrusion of rock materials
miter
the junction of two units at an angle of which the junction lines usually bisect on a 45 degree angle
modular multiple-cut (pattern-cut)
this refers to standard patterns used throughout the stone industry. These patterns are usually based on multiples of a given height. Stone that is multiple cut or pattern cut is pre-cut to allow typically for ¼ or ½ inch (6 or 13 mm) joints or beds
moldings
decorative stone deviating from a plane surface by projections, curved profiles, recessed or any combination thereof
mortar
a plastic mixture of cement, lime, sand, and water used to bond masonry units
mosaic
a veneering which is generally irregular with no definite pattern. Nearly all the stone used in a mosaic pattern is irregular in shape

N

natural bed
the setting of the stone on the same plane as it was formed in the ground. This generally applies to all stratified materials
natural cleft
this generally pertains to stones which are formed in layers in the ground. When such stones are cleaved or separated along a natural seam the remaining surface is referred to as a natural cleft surface
nicked bit finish
obtained by planing the stone with a planer tool in which irregular nicks have been made in the cutting edge
non-staining mortar
mortar composed of materials which individually or collectively do not contain material that will stain, usually having a very low alkali content

O

obsidian
a glassy phase of lava
ogee
a stone profile with a reverse curved edge: concave above, convex below
onyx marble
a dense, crystalline form of lime carbonate deposited usually from cold water solutions. Generally translucent and shows a characteristic layering due to mode of accumulation
oolitic limestone
a calcite-cemented calcareous stone formed of shells and shell fragments, practically non-crystalline in character. It is found in massive deposits located almost entirely in Lawrence, Monroe and Owen Counties, IN and in Alabama, Kansas, and Texas. This limestone is characteristically a freestone, without cleavage planes, possessing a remarkable uniformity of composition, texture and structure. It possesses a high internal elasticity, adapting itself without damage to extreme temperature changes
opalized
the introduction into a rock of siliceous material in the form of opal, hydrous silicate
out of wind
to be out of wind is to have the arris of the stone not in parallel or perpendicular lines. Stone which is out of wind has an irregular or rustic appearance

P

palletized
a system of stacking stone on wooden pallets. Stone which comes palletized is easily moved and transported by modern handling equipment. Palletized stone generally arrives at the job site in better condition than unpalletized material
panel
a finished stone unit used on walls
parapet wall
that part of any wall entirely above the roof line
parging
plastering a cementitious coating of mortar onto a surface, often used for damp-proofing
parquetry
an inlay of stone floors in geometrical or other patterns
paving
stone used as an exterior wearing surface, as in patios, walkways, driveways, etc. (see flooring)
perforated wall
one which contains a considerable number of relatively small openings. Often called pierced wall or screen wall
perrons
slabs of stone set on other stones serving as steps and arches in gardens
phenocryst
in igneous rocks, the relatively large and conspicuous crystals in a finer-grained matrix or ground mass
pilaster
an engaged pier of shallow depth; in classical architecture it follows the height and width of related columns, with similar base and cap
pitched stone
stone having arris clearly defined; face, however, is roughly cut with pitching chisel used along the line which becomes the arris
plinths
the lower square part of the base of a column. A square base or a lower block, as of a pedestal. The base block at the juncture of baseboard and trim around an opening
plucked finish
obtained by rough planing the surface of stone, breaking or plucking out small particles to give rough texture
pointing
the filling and tooling of mortar joints with mortar or caulking compounds
polished finish
the finest and smoothest finish available in stone characterized by a gloss or reflective property. Generally only possible on hard, dense materials
porphyry
an igneous rock in which relatively large and conspicuous crystals (phenocrysts) are set in a matrix of finer crystals
pressure relieving joint
an open horizontal joint below the supporting angle or hanger located at approximately every floor line and not over 15 feet (4.6 m) apart horizontally and every 20 to 30 feet (6 to 9m) vertically to prevent the weight from being transmitted to the masonry below. These joints are to be caulked with a resilient non-staining material to prevent moisture penetration
processing
the work involved in transforming building stone from quarry blocks to cut or finished stone. This includes primary sawing into slabs. It may also include both hand and mechanical techniques such as sawing, drilling, grinding, honing, polishing, and carving
projections
this refers to the pulling out of stones in a wall to give an effect of ruggedness. The amount of each stone is pulled out can vary between ½ and 11/2 inches (1.3 to 3.8cm). Stones are either pulled out at the same degree at both ends or sometimes one end is pulled out, leaving the other end flush with the majority of veneer
pumice
and exceptionally cellular, glassy lava resembling a solid froth

Q

quarry
an excavation where usable stone is extracted from the ground
quartz
a silicon dioxide mineral that occurs in colorless and transparent or colored hexagonal crystals and also in crystalline masses. One of the most common minerals, the chief constituent of sandstone
quartzite
a compact granular rock composed of quartz crystals, usually so firmly cemented as to make the mass homogeneous. The stone is generally quarried in stratified layers, the surfaces of which are unusually smooth. Its crushing and tensile strengths are extremely high; the color range is wide
quartzitic sandstone
a sandstone with a high concentration of quartz grains and siliceous cement
quirt
a groove separating a bed or other moulding from the adjoining members
quoins
stones at the corner of a wall emphasized by size, projection, rustification, or by a different finish

R

range
a course of any thickness that is continued across the entire face. All range course need not be of the same thickness
recess
a sinkage in a wall plane
reglet
a recess used to receive and secure flashing
relief or relieve
ornament in relief. The ornament or figure can be slightly, half, or greatly projected
relieving arch
one built over a lintel, flat arch or smaller arch to divert loads, thus relieving the lower member from excessive loading. Also known as discharging or safety arch
return
the right angle turn of a molding
return head
stone facing with the finish appearing on both the face and the edge of the same stone, as on the corner of a building
reveal
the depth of stone between its outer face and a window or door set in an opening
ribbon
narrow bands of rock differing to various degrees in chemical composition and color from the main body of the slate or stone; in other words, bands
rift
the most pronounced (see "grain") direction of splitting or cleavage of a stone. Rift and grain may be obscure, as in some granites, but are important in both quarrying and processing stone
riprap
irregular shaped stones used for facing bridge abutments and fills. Stone thrown together without order to form a foundation or sustaining walls
rise
the word "rise" refers to the heights of stone. Generally used in reference to veneer stone
rock
the integral part of the earth's crust composed of an aggregate of grains of one or more minerals. (stone is the commercial term applied to quarry products)
rock (pitch) face
this is similar to split face, except that the face of the stone is pitched to a given line and plane producing a bold appearance, rather than the comparatively straight face obtained in split face
rodding
reinforcement of a structurally unsound marble by cementing reinforcing rods into grooves or channels cut into the back of the slab
roman arch
semi-circular arch
rose window
a circular stone window fitted with carved tracery
rough sawn
a marble surface finish accomplished by the gangsawing process
rubbed finish
mechanically rubbed for smoother finish
rubble
a product term applied to dimension stone used for building purposes, chiefly walls and foundations, and consisting of irregularly shaped pieces, partly trimmed or squared, generally with one split or finished face, and selected and specified with a size range
rustication
chamfers or square sinkings around the face edges of individual stones to create shadows and to give an appearance of greater weight to the lower part of a building. When only the horizontal joints are sunk, the device is known as banded rustication
rustification
recessing the margin of cut stone so that when placed together a channel is formed at each joint

S

saddle
a flat strip of stone projecting above the floor between the jambs of the door; a threshold
sandblasted
a dull non-glossy finish applied to stone; usually accomplished by blasting air blended with sand across the surface
sand-sewn finish
the surface left as the stone comes from the gangsaw. Moderately smooth, granular surface varying with the texture and grade of stone
sandstone
a sedimentary rock consisting usually of quartz, cemented with silica, iron oxide or calcium carbonate. Sandstone is durable, has a very high crushing and tensile strength, and a wide range of colors and textures. Varieties of sandstone are commonly designated by the kind and prominence of interstitial and bonding materials, as siliceous sandstone (bonding material primarily silica), calcareous sandstone (calcium carbonate prominent as bonding material or as accessory grains or both), argillaceous sandstone (clay minerals prominent as interstitial or bonding materials, or as thin laminac), ferruginous sandstone (iron oxide or hydroxide minerals, or as thin laminac), ferruginous sandstone (iron oxide or hydroxide minerals {hematic, limonite, et al} as interstitial or as bonding materials in sufficient amount to impart appreciable color to the stone): brownstone (ferruginous sandstone of dark brown or reddish brown color),
arkose, arkosic sandstone, or feldspathic sandstone (a sandstone that contains an abundance of grains of feldspar), conglomerate (a sandstone composed in large part of rounded pebbles, also called puddingstone). The term "brownstone" was applied originally to certain Trassic sandstones of the Connecticut Valley in Massachusetts (Longmeadow sandstone), Connecticut (Portland sandstone), and to similarly appearing reddish-brown sandstone quarried in and near Hummelstown, PA. Thus the term originally had geographic significance, but such geographic limitation is undesirable
sawed edge
a clean cut edge generally achieved by cutting with a diamond blade, gang saw or wire saw
sawed face
a finish obtained from the process used in producing building stone. Varies in texture from smooth to rough and coincident with the type of materials used in sawing; characterized as diamond sawn, sand sawn, chat sawn, and shot sawn
scale
thin lamina or paper-like sheets of rock, often loose, and interrupting an otherwise smooth surface on the stone
schist
a loose term applying to foliated metamorphic (recrystallized) rock characterized by thin foliae that are composed predominantly of minerals of thin platy or prosmatic habits and whose long dimensions are oriented in approximately parallel positions along the planes of foliation. Because of this foliated structure, schists split readily along these planes and so possess a pronounced rock cleavage. The more common schists are composed of the micas and other mica-like minerals (such as chlorite) and generally contain subordinate quartz and/or feldspar of comparatively fine-grained texture; all graduations exist between schist and gneiss (coarsely foliated feldspathic rocks)
scoria
irregular masses of lava resembling clinker of slag; may be cellular (vesticular), dark-colored and heavy
scotia
a concave molding
sculpture
statuary cut from stone by a sculptor using hand tools and polishing materials
semi-rubbed
a finish achieved by rubbing (by hand or machine) the rough or high spots off the surface to be used, leaving a certain amount of the natural surface along with the smoothed areas
serpentine
a hydrous magnesium silicate material of igneous origin, generally a very dark green color with markings of white, light green or black. One of the hardest varieties of natural building stone
serpetinev
marble characterized by a prominent amount of the mineral serpentine
setting space
a term used to indicate the distance from the finished face of the marble to the face of the back-up wall
shaped stone
cut stone which has been carved, ground or otherwise processed
shear
a type of stress; a body is in shear when it is subjected to a pair of equal forces which are opposite in direction and which act along parallel planes
shot-sawn
description of a finish obtained by using steel shot in the gang sawing process to produce random markings for a rough surface texture.
shot-sawn finish
a rough gangsaw finish produced by sawing with chilled steel shots
sill
a flat stone used under windows, doors, and other masonry openings
siltstone
a fine-grained non-carbonate clastic rock composed of at least 67 per cent of detrital grains of quartz and silicate minerals of silt size. Siltstones are rarely marketed as such but commonly are considered as fine-grained sandstones. This class of sediments is texturally transitional between sandstones and shales (mudstones)
siliceous
flagstones fall within this category. The term is included in these definitions chiefly to explain the relationship of some siliceous flagstones to the sandstone category
slab
a lengthwise cut of large quarry block of stone approximately 5'x 8'in size
slate
a very fine-grained metamorphic rock derived from sedimentary rock shale. Characterized by an excellent parallel cleavage entirely independent of original bedding, by which cleavage the rock may be split easily into relatively thin slabs. Essential mineral constituents of slates are usually members of the mica group, commonly sericite, muscovite, and paragonite; of the clay group, chiefly illite and kaolinite; and of the chlorite group. Common accessory minerals are iron oxides, calcite, quarts, and feldspar. Other minerals may be present also as minor accessories. Most slates are derived from shales. Others are derived from fine-grained igneous rock, chiefly volcanic tuffs, but these are rare and of little commercial importance
slip sill
a stone sill set between jambs (see lug sill)
smooth finish
description of the finish produced by planer machines plus the removal of objectionable tool marks. Also known as "smooth planer finish" and "smooth machine finish"
snapped edge, quarry cut or broken edge
a natural breaking of a stone either by hand or machine. The break should be at right angles to the top and bottom surfaces
soapstone
a massive variety of talc with a soapy or greasy feel used for hearths, washtubs, table tops, carved ornaments, chemical laboratories, etc., known for its stain-proof qualities
soffit
the finished, exposed underside of a lintel, arch or portico
sound stone
stone which is free of cracks, fissures, or other physical defects
spall
a stone fragment that has split or broken off
spalls
sizes may vary from chip-size to one and two man stones. Spalls are primarily used for taking up large voids in rough rubble or mosaic patterns
spandrel wall
that part of a curtain wall above the top of a window in one story and below the sill of the window in the story above
splay
a beveled or slanted surface
spline
a thin strip of material, such as wood or metal, inserted into the edges of two stone pieces or stone tiles to make a butt joint between them
split
division of a rock by cleavage
split face (sawed bed)
usually split face is sawed on the beds and is split either by hand or with machine so that the surface face of the stone exhibits the natural quarry texture
splitstone finish
obtained by sawing to accurate heights then breaking by machine to required bed widths. (normal bed widths are 3 ½ inches [90 mm])
spot or spotting
an adhesive contact, usually of plaster of paris, applied between the back of marble veneer and the face of the back-up wall to plumb or secure standing marble
stacked bond
stone that is cut to one dimension and installed with unbroken vertical and horizontal joints running the entire length and height of the veneered area
start
a small fissure
statue
a sculpture of a human or animal figure
sticking
an expression used in the marble finishing trade to describe the process of cementing together broken slabs or pieces of marble
stone
sometimes synonymous with rock, but more properly applied to individual blocks, masses or fragments taken from their original formation or considered for commercial use
stool
a flat stone, generally polished, used as an interior sill
stratification
a structure produced by deposition of sediments in beds or layers (strata), laminae, lenses, wedges, and other essentially tabular units
strip rubble
generally speaking, strip rubble comes from a ledge quarry, the beds of the stone, while uniformly straight, are of the natural cleft as the stone is removed from the ledge, and then split by machine to approximately 4 inch (100 mm) widths
strips
long pieces of stone, usually low height ashlar courses, where length to height ratio is at maximum for the material used
styrolite
a longitudinally streaked, columnar structure occurring in some marbles and of the same material as the marble in which it occurs
surround
an efframement

T

tablet
a small, flat slab or surface of stone, especially one bearing or intended to bear an inscription, carving or the like
template
a pattern for repetitive marking or fabricating operation; "safe" a water closet base
terrazzo
a type of concrete in which chips or pieces of stone, usually marble, are mixed with cement and are ground to a flat surface, exposing the chips, which take a high polish
texture
three dimensional surface enrichment independent of color
thin stone
stone slabs generally of two inches or less in thickness
thin marble
a fabricated marble unit of 2 inches (50 mm) thick
tile
a thin modular stone unit
tolerance
dimensional allowance made for the inability of men and machines to fabricate a product of exact dimensions
throat
the name sometimes given to the small groove under the windowsill or dripstone, intended of deflect rain water from the wall face
tooled finished
customarily are four, six or eight parallel, concave grooves to the inch
tracery
ornamentation of panels, circular windows, window heads, etc
translucence
permitting light to pass through with little diffusing. Certain marble varieties are translucent
travertine
a form of limestone precipitated from ground waters, as in caves or in orifices of springs (see limestone group)
travertine limestone
a variety of limestone that has a partly crystalline or microcrystalline texture and porous or cellular layered structure, the cells being usually concentrated along certain layers and commonly displaying small stalactic forms
travertine marble
a variety of limestone regarded as a product of chemical precipitation from hot springs. Travertine is cellular with the cells usually concentrated in thin layers that display a stalactic structure. Some that take a polish are sold as marble and may be classified as travertine marble under the class of "Commercial Marble.
tread
a flat stone used as the top walking surface on steps
trim
stone used as decorative items only, such as sills, coping, enframements, etc., with the facing of another material
trimmer arch
a stone arch, usually a low-rise arch, used for supporting a fireplace hearth
tuff
cemented volcanic ash, many varieties included

U

undercut
cut so as to present and overhanging part

V

vein cut
cutting quarried marble or stone perpendicular to the natural bedding plane
veinings
colored markings in limestone, marble, alabaster, etc
veneer stone
any stone used as a decorative facing material which is not meant to be load-bearing
venting
creating an outlet in a wall for air and moisture to pass through. (see cavity vent.)
verd (or verde) antique
a marble composed chiefly of massive serpentine and capable of being polished. It is commonly crossed by veinlets of other minerals, chiefly carbonates of calcium and magnesium
vug
a cavity in rock, sometimes lined or filled with either amorphous or crystalline material, common in calcereous rocks such as marble or limestone

W

wall plate
a horizontal member anchored to a masonry wall to which other structural elements may be attached. Also called "head plate.
walls
one of the sides of a room or building connection floor and ceiling or foundation and roof:

- wall, bearing
a wall supporting a vertical load in addition to it own weight.
-wall, cavity
a wall in which the inner and outer wythes are separated by an air space but tied together with metal ties.
-wall, composite
a wall in which the facing and backing are of different materials and bonded together with bond stones to exert a common reaction under load.
-wall, veneer, or faced
a wall in which a thin facing and the backing are of different materials but not so bonded as to exert a common reaction under load.
-wall, wind (wined)
a twisting warp from cutting slabs in the gang saws.
-wall, wythe
the inner or outer part of a cavity wall.

wall tie
a bonder or metal piece which connects wythes of masonry to each other or to other materials
wall tie cavity
a rigid, corrosion-resistant metal tie which bonds two wythes of a cavity wall. It is usually steel, 3/16" in diameter and formed in a "Z" shape or a rectangle
warped walls
generally a condition experienced only in flagging or flagstone materials; very common with flagstone materials that are taken from the ground and used in their natural state. To eliminate warping in stones it would be necessary to further finish the material, by methods such as machining, sand rubbing, honing or polishing
wash
a sloped area, or the area water will run over
water bar
typically a strip in a reglet in window sill and stone below to prevent water passage
water table
a projection of lower masonry on the outside of the wall, slightly above the ground. Often a damp course is placed at the level of the water table to prevent upward penetration of ground water
waxing
an expression used in the marble finishing trade to indicate the filling of natural voids with color blended materials
wear
the removal of material or impairment of surface finishing through friction or impact use
weathering
natural alteration by either chemical or mechanical processes due to the action of constituents of the atmosphere, surface waters, soil and other ground waters, or to temperature changes; the inclined top surface of a stone such as a coping, cornice, or window sill
wedging
splitting of stone by driving wedges into planes of weakness
weep holes
openings placed in mortar joints of facing material at the level of flashing to permit the escape of moisture
wind
(wined) - a twisting warp from cutting slabs in the gang saws
wire saw
method of cutting stone by passing a twisted, multistrand wire over the stone and immersing the wire in a slurry of abrasive material
wythe
the inner or outer part of a cavity wall